CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS CV Chip Type, High Voltage / Long Life series High voltage (to 125V), Low ESR, High ripple current. Load life of 3000 hours at 105°C. SMD type : Lead free reflow soldering condition at 260°C peak correspondence. Compliant to the RoHS directive (2002/95/EC). CX CV High Temperature Specifications Item Performance Characteristics Category Temperature Range – 55 to +105°C Rated Voltage Range 16 to 125V Rated Capacitance Range 5.6 to 680µF ± 20% at 120Hz, 20°C Capacitance Tolerance Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C ESR ( Less than or equal to the specified value at 100kHz, 20°C 1) Leakage Current ( 2) Less than or equal to the specified value . After 2 minutes' application of rated voltage at 20°C Temperature Characteristics (Max.Impedance Ratio) Z+105°C / Z+20°C Z– 55°C / Z+20°C Endurance The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 3000 hours at 105°C. Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value Damp Heat (Steady State) The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 60°C, 90% RH. Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 10% of the initial capacitance value ( 3) 130% or less than the initial specified value 130% or less than the initial specified value Less than or equal to the initial specified value 1.25 1.25 (100kHz) After soldering the capacitor under the soldering conditions prescribed here, the capacitor shall meet the specifications listed at right, provided that it's temperature profile is measured at the capacitor top and the terminal. Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec. The duration for over +230°C temperature at capacitor surface shall not exceed 60 seconds. In the case of peak temp, less than 250°C, reflow soldering shall be two times maximum. In the case of peak temp, less than 260°C, reflow soldering shall be once. Measurement for solder temperature profile shall be made at the capacitor top and the terminal. Navy blue print on the case top Resistance to Soldering Heat Marking 1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120 minutes at 105°C. 3 Initial value : The value before test of examination of resistance to soldering. Dimensions φD + 0.5 MAX. C±0.2 2 3 4 5 6 7 8 9 10 11 12 13 14 PCV 1 V 8 2 0 MC L 1 GS Taping code Configuration A±0.2 E B±0.2 Size code Capacitance toleranc (±20%) Rated capacitance (82µF) L +0.1 - 0.4 Voltage (V:35V) Series 1 0.5 MAX. Lot No. CV 82 V 012 Capacitance Type numbering system (Example : 35V 82µF) Positive Plastic platform 0.3 MAX. Rated voltage (35V) Negative Series name H Type (mm) Size φ6.3 × 6L φ8 × 7L φ8 × 10L φ8 × 12L φ10 × 8L φ10 × 10L φ10 × 12.7L φD 6.3 8.0 8.0 8.0 10.0 10.0 10.0 L 5.9 6.9 9.9 11.9 7.9 9.9 12.6 A 7.3 9.0 9.0 9.0 11.0 11.0 11.0 B 6.6 8.3 8.3 8.3 10.3 10.3 10.3 C 6.6 8.3 8.3 8.3 10.3 10.3 10.3 E 2.1 3.2 3.2 3.2 4.6 4.6 4.6 H 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 Dimension table in next page. Voltage V 16 20 25 35 50 63 80 100 125 Code C D E V H J K 2A 2B CAT.8100B CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS CV series Standard Ratings Rated Voltage (V)(code) 16 (1C) Surge Voltage (V) 18.4 Rated Capacitance (µF) Case Size φD × L (mm) tan δ Leakage Current (µA) 56 6.3 × 6 0.12 179 82 6.3 × 6 0.12 262 100 8×7 0.12 150 8×7 220 Rated Ripple (mArms) Part Number 50 1000 PCV1C560MCL1GS 47 1300 PCV1C820MCL2GS 320 36 1500 PCV1C101MCL1GS 0.12 480 34 1700 PCV1C151MCL2GS 0.12 704 27 2000 PCV1C221MCL6GS 220 8 × 10 10 × 8 0.12 704 31 2000 PCV1C221MCL1GS 270 8 × 10 0.12 864 21 3800 PCV1C271MCL7GS 270 8 × 12 0.12 864 26 2300 PCV1C271MCL1GS 270 10 × 8 0.12 864 24 3200 PCV1C271MCL2GS 330 10 × 10 0.12 1056 26 2400 PCV1C331MCL1GS 390 8 × 12 0.12 1248 20 4100 PCV1C391MCL2GS 470 10 × 10 10 × 12.7 0.12 1504 21 3900 PCV1C471MCL2GS 0.12 1504 25 2800 PCV1C471MCL1GS 10 × 12.7 6.3 × 6 0.12 2176 19 4400 PCV1C681MCL2GS 0.12 188 55 1000 PCV1D470MCL1GS 6.3 × 6 8×7 0.12 224 48 1300 PCV1D560MCL2GS 0.12 272 45 1300 PCV1D680MCL1GS 0.12 400 42 1400 PCV1D101MCL2GS 0.12 600 28 2000 PCV1D151MCL6GS 0.12 600 33 1900 PCV1D151MCL1GS 0.12 720 25 3100 PCV1D181MCL2GS 8 × 10 8 × 12 0.12 880 22 3700 PCV1D221MCL7GS 0.12 880 27 2300 PCV1D221MCL1GS 8 × 12 10 × 10 0.12 1080 21 4000 PCV1D271MCL2GS 0.12 1080 27 2300 PCV1D271MCL1GS 10 × 10 10 × 12.7 0.12 1320 22 3800 PCV1D331MCL2GS 0.12 1320 26 2700 PCV1D331MCL1GS 10 × 12.7 6.3 × 6 0.12 1880 20 4300 PCV1D471MCL2GS 0.12 165 60 1000 PCV1E330MCL1GS 6.3 × 6 8 ×7 0.12 235 49 1300 PCV1E470MCL2GS 0.12 280 50 1300 PCV1E560MCL1GS 8 ×7 8 × 10 0.12 410 47 1400 PCV1E820MCL2GS 0.12 600 29 1900 PCV1E121MCL6GS 10 × 8 8 × 10 0.12 600 35 1800 PCV1E121MCL1GS 0.12 750 23 3600 PCV1E151MCL7GS 0.12 750 28 2200 PCV1E151MCL1GS 150 8 × 12 10 × 8 0.12 750 26 3000 PCV1E151MCL2GS 180 10 × 10 0.12 900 28 2300 PCV1E181MCL1GS 220 8 × 12 10 × 10 0.12 1100 22 3800 PCV1E221MCL2GS 0.12 1350 23 3700 PCV1E271MCL2GS 10 × 12.7 10 × 12.7 0.12 1350 27 2700 PCV1E271MCL1GS 0.12 1950 21 4200 PCV1E391MCL2GS 18 6.3 × 6 0.12 126 64 900 PCV1V180MCL1GS 22 6.3 × 6 8×7 0.12 154 50 1300 PCV1V220MCL2GS 0.12 189 55 1200 PCV1V270MCL1GS 8×7 8 × 10 0.12 273 52 1400 PCV1V390MCL2GS 0.12 392 31 1900 PCV1V560MCL1GS 10 × 8 8 × 10 0.12 476 37 1800 PCV1V680MCL1GS 0.12 574 24 3600 PCV1V820MCL7GS 8 × 12 10 × 8 0.12 574 29 2200 PCV1V820MCL1GS 0.12 574 27 3000 PCV1V820MCL2GS 10 × 10 8 × 12 0.12 700 29 2200 PCV1V101MCL1GS 0.12 840 23 3800 PCV1V121MCL7GS 0.12 840 24 3700 PCV1V121MCL2GS 150 10 × 10 10 × 12.7 0.12 1050 28 2600 PCV1V151MCL1GS 180 10 × 12.7 0.12 1260 22 4100 PCV1V181MCL2GS 470 680 47 56 68 100 150 150 20 (1D) 23.0 180 220 220 270 270 330 330 470 33 47 56 82 120 120 25 (1E) 28.7 150 150 270 270 390 27 39 56 68 35 (1V) 40.2 ESR (mΩ) 。 (at 100kHz 20 C) 82 82 82 100 120 120 8×7 8 × 10 10 × 8 10 × 8 CAT.8100B CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS CV series Standard Ratings Rated Voltage (V)(code) Surge Voltage (V) Rated Capacitance (µF) 57.5 82 81 800 PCV1H8R2MCL1GS 55 1200 PCV1H120MCL2GS 15 0.12 150 63 1100 PCV1H150MCL1GS 22 8×7 0.12 220 60 1300 PCV1H220MCL2GS 33 8 × 10 0.12 330 36 1700 PCV1H330MCL6GS 33 0.12 330 49 1500 PCV1H330MCL1GS 39 10 × 8 8 × 12 0.12 390 34 2000 PCV1H390MCL1GS 47 8 × 10 0.12 470 29 3300 PCV1H470MCL7GS 47 10 × 8 0.12 470 37 2600 PCV1H470MCL2GS 47 10 × 10 0.12 470 30 2200 PCV1H470MCL1GS 56 8 × 12 0.12 560 28 3400 PCV1H560MCL2GS 68 10 × 10 10 × 12.7 0.12 680 29 3400 PCV1H680MCL2GS 0.12 680 29 2600 PCV1H680MCL1GS 10 × 12.7 6.3 × 6 0.12 1000 27 3600 PCV1H101MCL2GS 0.12 71 105 700 PCV1J5R6MCL1GS 6.3 × 6 8 ×7 0.12 103 56 1200 PCV1J8R2MCL2GS 0.12 126 75 1000 PCV1J100MCL1GS 8 ×7 8 × 10 0.12 151 70 1100 PCV1J120MCL2GS 0.12 277 37 1700 PCV1J220MCL6GS 10 × 8 8 × 10 0.12 277 56 1400 PCV1J220MCL1GS 0.12 340 30 3200 PCV1J270MCL7GS 8 × 12 10 × 8 0.12 340 35 2000 PCV1J270MCL1GS 0.12 340 38 2500 PCV1J270MCL2GS 10 × 10 8 × 12 0.12 416 31 2200 PCV1J330MCL1GS 0.12 491 29 3400 PCV1J390MCL2GS 10 × 10 10 × 12.7 0.12 592 30 3300 PCV1J470MCL2GS 0.12 592 30 2500 PCV1J470MCL1GS 10 × 12.7 8 × 10 0.12 706 28 3400 PCV1J560MCL2GS 0.12 160 43 1600 PCV1K100MCL1GS 8 × 12 10 × 10 0.12 192 41 1800 PCV1K120MCL1GS 0.12 240 39 1900 PCV1K150MCL1GS 10 × 12.7 8 × 10 0.12 352 38 2200 PCV1K220MCL1GS 0.12 136 48 1500 PCV2A6R8MCL1GS 8 × 12 10 × 10 0.12 200 45 1700 PCV2A100MCL1GS 0.12 240 42 1900 PCV2A120MCL1GS 10 × 12.7 8 × 10 0.12 360 41 2100 PCV2A180MCL1GS 0.12 170 93 1100 PCV2B6R8MCL1GS 0.12 205 84 1300 PCV2B8R2MCL1GS 12 8 × 12 10 × 10 0.12 300 69 1400 PCV2B120MCL1GS 15 10 × 12.7 0.12 375 48 2000 PCV2B150MCL1GS 10 12 22 22 27 27 27 33 39 47 47 56 10 12 15 22 6.8 100 (2A) 115 10 12 18 6.8 125 (2B) 143 Part Number 120 8.2 92.0 Rated Ripple (mArms) 0.12 5.6 80 (1K) ESR (mΩ) 。 (at 100kHz 20 C) 0.12 100 72.4 Leakage Current (µA) 6.3 × 6 8×7 68 63 (1J) tan δ 6.3 × 6 8.2 12 50 (1H) Case Size φD × L (mm) 8.2 Rated ripple current (mArms) at 105°C 100kHz No marked, 1 will be put at 12th digit of type numbering system. : In this case, 2 will be put at 12th digit of type numbering system. : In this case, 6 will be put at 12th digit of type numbering system. : In this case, 7 will be put at 12th digit of type numbering system. Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity. CAT.8100B