SCES557A − MARCH 2004 − REVISED MAY 2004 D Qualification in Accordance With D D D D D D D D D D Ioff Supports Partial-Power-Down Mode AEC-Q100† Qualified for Automotive Applications Customer-Specific Configuration Control Can Be Supported Along With Major-Change Approval Supports 5-V VCC Operation Inputs Accept Voltages to 5.5 V Max tpd of 4.7 ns at 3.3 V Low Power Consumption, 10-µA Max ICC ±24-mA Output Drive at 3.3 V Typical VOLP (Output Ground Bounce) <0.8 V at VCC = 3.3 V, TA = 25°C Typical VOHV (Output VOH Undershoot) >2 V at VCC = 3.3 V, TA = 25°C Operation Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II ESD Protection Exceeds JESD 22 − 2000-V Human-Body Model (A114-A) − 1000-V Charged-Device Model (C101) D D DCT OR DCU PACKAGE (TOP VIEW) 1A 1B 2Y GND 1 8 2 7 3 6 4 5 VCC 1Y 2B 2A † Contact factory for details. Q100 qualification data available on request. description/ordering information This dual 2-input positive-AND gate is designed for 1.65-V to 5.5-V VCC operation. The SN74LVC2G08 performs the Boolean function Y + A • B or Y + A ) B in positive logic. This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down. ORDERING INFORMATION −40°C to 85°C ORDERABLE PART NUMBER PACKAGE‡ TA SSOP − DCT Tape and reel SN74LVC2G08IDCTRQ1 TOP-SIDE MARKING§ C08_ _ _ SN74LVC2G08IDCURQ1¶ VSSOP − DCU Tape and reel C08_ ‡ Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. § DCT: The actual top-side marking has three additional characters that designate the year, month, and assembly/test site. DCU: The actual top-side marking has one additional character that designates the assembly/test site. ¶ Product Preview FUNCTION TABLE (each gate) INPUTS A B OUTPUT Y H H H L X L X L L Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 2004, Texas Instruments Incorporated ! "#$ ! %#&'" ($) (#"! " !%$""! %$ *$ $! $+! !#$! !(( ,-) (#" %"$!!. ($! $"$!!'- "'#($ $!. '' %$$!) POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SCES557A − MARCH 2004 − REVISED MAY 2004 logic diagram (positive logic) 1A 1B 2A 2B 1 2 7 1Y 5 6 3 2Y absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 6.5 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 6.5 V Voltage range applied to any output in the high-impedance or power-off state, VO (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 6.5 V Voltage range applied to any output in the high or low state, VO (see Notes 1 and 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to VCC + 0.5 V Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −50 mA Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −50 mA Continuous output current, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±100 mA Package thermal impedance, θJA (see Note 3): DCT package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220°C/W DCU package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output current ratings are observed. 2. The value of VCC is provided in the recommended operating conditions table. 3. The package thermal impedance is calculated in accordance with JESD 51-7. 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SCES557A − MARCH 2004 − REVISED MAY 2004 recommended operating conditions (see Note 4) Operating VCC VIH Supply voltage High-level input voltage VIL Low-level input voltage VI VO Input voltage Data retention only VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 3 V to 3.6 V VCC = 4.5 V to 5.5 V VCC = 2.3 V ∆t/∆v Low-level output current Input transition rise or fall rate 5.5 0.65 × VCC 1.7 V 2 0.7 × VCC 0.35 × VCC 0.7 0.8 V 0.3 × VCC 0 5.5 V 0 VCC −4 V −8 mA −24 −32 4 8 16 VCC = 3 V UNIT V 1.5 −16 VCC = 3 V VCC = 4.5 V VCC = 1.65 V IOL 1.65 VCC = 3 V to 3.6 V VCC = 4.5 V to 5.5 V Output voltage High-level output current MAX VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 1.65 V VCC = 2.3 V IOH MIN mA 24 VCC = 4.5 V VCC = 1.8 V ± 0.15 V, 2.5 V ± 0.2 V 32 VCC = 3.3 V ± 0.3 V VCC = 5 V ± 0.5 V 10 20 ns/V 5 TA Operating free-air temperature −40 85 °C NOTE 4: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 SCES557A − MARCH 2004 − REVISED MAY 2004 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS VCC 1.65 V to 5.5 V IOH = −100 mA IOH = −4 mA IOH = −8 mA IOH = −16 mA VOH MAX 2.3 3.8 0.1 1.65 V 0.45 2.3 V 0.3 0.4 3V IOL = 24 mA VI = 5.5 V or GND VI or VO = 5.5 V 0.55 0 to 5.5 V 0 VI = 5.5 V or GND, One input at VCC − 0.6 V, IO = 0 Other inputs at VCC or GND 1.65 V to 5.5 V 3 V to 5.5 V Ci VI = VCC or GND † All typical values are at VCC = 3.3 V, TA = 25°C. V 0.55 4.5 V IOL = 32 mA UNIT V 1.65 V to 5.5 V IOL = 8 mA IOL = 16 mA ICC ∆ICC 1.9 4.5 V IOL = 100 mA IOL = 4 mA A or B inputs 2.3 V 3V IOH = −32 mA II Ioff 1.65 V VCC−0.1 1.2 TYP† 2.4 IOH = −24 mA VOL MIN 3.3 V ±5 mA ±10 mA 10 mA 500 mA 5 pF switching characteristics over recommended operating free-air temperature range (unless otherwise noted) (see Figure 1) PARAMETER tpd FROM (INPUT) TO (OUTPUT) A or B Y VCC = 1.8 V ± 0.15 V VCC = 2.5 V ± 0.2 V VCC = 3.3 V ± 0.3 V VCC = 5 V ± 0.5 V MIN MAX MIN MAX MIN MAX MIN MAX 2.6 9 1 5.1 1 4.7 1 3.8 UNIT ns operating characteristics, TA = 25°C PARAMETER Cpd 4 Power dissipation capacitance TEST CONDITIONS f = 10 MHz POST OFFICE BOX 655303 VCC = 1.8 V TYP VCC = 2.5 V TYP 17 • DALLAS, TEXAS 75265 17 VCC = 3.3 V TYP 17 VCC = 5 V TYP 20 UNIT pF SCES557A − MARCH 2004 − REVISED MAY 2004 PARAMETER MEASUREMENT INFORMATION RL From Output Under Test CL (see Note A) VLOAD Open S1 GND RL TEST S1 tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open VLOAD GND LOAD CIRCUIT INPUTS VCC 1.8 V ± 0.15 V 2.5 V ± 0.2 V 3.3 V ± 0.3 V 5 V ± 0.5 V VI tr/tf VCC VCC 3V VCC ≤2 ns ≤2 ns ≤2.5 ns ≤2.5 ns VM VLOAD CL RL V∆ VCC/2 VCC/2 1.5 V VCC/2 2 × VCC 2 × VCC 6V 2 × VCC 30 pF 30 pF 50 pF 50 pF 1 kΩ 500 Ω 500 Ω 500 Ω 0.15 V 0.15 V 0.3 V 0.3 V VI Timing Input VM 0V tw tsu VI Input VM VM th VI Data Input VM VM 0V 0V VOLTAGE WAVEFORMS PULSE DURATION VOLTAGE WAVEFORMS SETUP AND HOLD TIMES VI VM Input VM 0V tPLH tPHL VOH VM Output VM VOL tPHL Output Waveform 1 S1 at VLOAD (see Note B) tPLH VM VM VM 0V tPZL tPLZ VLOAD/2 VM tPZH VOH Output VI Output Control VM VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES INVERTING AND NONINVERTING OUTPUTS Output Waveform 2 S1 at GND (see Note B) VOL + V∆ VOL tPHZ VM VOH − V∆ VOH ≈0 V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES LOW- AND HIGH-LEVEL ENABLING NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω. D. The outputs are measured one at a time, with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. H. All parameters and waveforms are not applicable to all devices. Figure 1. Load Circuit and Voltage Waveforms POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 MECHANICAL DATA MPDS049B – MAY 1999 – REVISED OCTOBER 2002 DCT (R-PDSO-G8) PLASTIC SMALL-OUTLINE PACKAGE 0,30 0,15 0,65 8 0,13 M 5 0,15 NOM ÇÇÇÇÇ ÇÇÇÇÇ ÇÇÇÇÇ ÇÇÇÇÇ 2,90 2,70 4,25 3,75 Gage Plane PIN 1 INDEX AREA 1 0,25 4 0° – 8° 3,15 2,75 0,60 0,20 1,30 MAX Seating Plane 0,10 0,10 0,00 NOTES: A. B. C. D. 4188781/C 09/02 All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion Falls within JEDEC MO-187 variation DA. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2004, Texas Instruments Incorporated