DATA SHEET MOS INTEGRATED CIRCUIT µPD16510 VERTICAL DRIVER FOR CCD SENSOR The µPD16510 is a vertical driver dedicated for CCD area image sensors that incorporates a level conversion circuit and a three-level output function. It contains a CCD vertical register driver (4 channels) and a VOD shutter driver (1 channel). The µPD16510, which uses the CMOS process, provides optimum transmission delay and output ON resistance characteristics for the vertical drive of CCD sensors. It can be used for low-voltage logic (logic power-supply voltage: 2.0 to 5.5 V). FEATURES • CCD vertical register driver : 4 channels, VOD shutter driver: 1 channel • Small package : 20-pin plastic shrink SOP (225 mil) • High breakdown voltage : 33 V MAX. • Low output ON resistance : 30 Ω TYP. • Low voltage operation (logic power-supply voltage: 2.0 to 5.5 V) • Latch-up free • Pin-compatible with µPD16506 (CCD driver) APPLICATIONS • Camcorders ORDERING INFORMATION Part Number Package µPD16510GR-8JG 20-pin plastic shrink SOP (225 mil) The information in this document is subject to change without notice. Document No. S12191EJ2V0DS00 (2nd edition) (Previous No. IC-3448) Date Published May 1997 N Printed in Japan The mark shows major revised points. 1994 µPD16510 BLOCK DIAGRAM Vsb 20 VDD1 16 VSS 2 TI1 7 4 VDD2a 19 VDD2b VDD1 VDD2a Three level 5 TO1 3 BO1 VSS PG1 VDD2b 8 Two level BI1 TI2 9 14 VSS Input interface (2.0 to 5.5 V) VDD1 VDD2a Three level PG2 13 BI2 12 VSS VDD2b Two level SUBI 10 NC 11 18 BO2 VSS Vsb Two level 2 VCC 6 GND 15 17 TO2 1 VSS SUBO µPD16510 PIN CONFIGURATION 20-pin plastic shrink SOP (225 mil) SUBO VSS BO1 VDD2a TO1 VCC TI1 PG1 BI1 SUBI Remark 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 Vsb VDD2b BO2 TO2 VDD1 GND TI2 PG2 BI2 NC The µPD16510 is pin-compatible with the µPD16506 (CCD driver). However, the VOD shutter drive pulse input polarity switching pin (SSP) of the µPD16506 corresponds to the GND pin in the µPD16510 (pin 15). PIN FUNCTIONS No. Symbol I/O Pin Function 1 SUBO O VOD shutter drive pulse output 2 VSS – VL power supply 3 BO1 O Two-level pulse output 4 VDD2a – VMa (Three-level driver) power supply 5 TO1 O Three-level pulse output 6 VCC – Logic power supply 7 TI1 I Three-level driver input (See Functions table on p. 4) 8 PG1 I 9 BI1 I Two-level driver input (See Functions table on p. 4) 10 SUBI I VOD shutter drive pulse input 11 NC – Non connect 12 BI2 I Two-level driver input (See Functions table on p. 4) 13 PG2 I Three-level driver input (See Functions table on p. 4) 14 TI2 I 15 GND – Ground 16 VDD1 – VH power supply 17 TO2 O Three-level pulse output 18 BO2 O Two-level pulse output 19 VDD2b – VMb (Two-level driver) power supply 20 Vsb – VHH (for SUB drive) power supply 3 µPD16510 FUNCTIONS VL = VSS, VMa = VDD2a, VMb = VDD2b, VH = VDD1, VHH = Vsb Pin TO1 Pin TO2 Input Input Output (TO1) TI1 PG1 L L L Output (TO2) TI2 PG2 VH L L VH H VMa L H VMa H L VL H L VL H H H H Pin BO1 Input Pin BO2 Output (BO1) BI1 Input Pin SUBO Output (BO2) BI2 Input Output (SUBO) SUBI L VMb L VMb L VHH H VL H VL H VL Usage Caution Because the µPD16510 contains a PN junction (diode) between VDD2 → VDD1, if the voltage is VDD2 > VDD1, an abnormal current will result. Therefore, apply power in the sequence VDD1 → VDD2, or apply power simultaneously to VDD1 and VDD2. 4 µPD16510 ELECTRICAL SPECIFICATIONS ABSOLUTE MAXIMUM RATINGS (Unless otherwise specified, TA = 25 ˚C, GND = 0 V) Parameter Symbol Conditions Rating Unit Power supply voltage VCC VSS–0.3 to VSS +20.0 V Power supply voltage VDD1 VSS–0.3 to VSS +33.0 V Power supply voltage VDD2 VSS–0.3 to VSS +33.0 V Power supply voltage Vsb VSS–0.3 to VSS +33.0 V Input voltage VI VSS–0.3 to V CC+0.3 V Operating ambient temperature TA –25 to +85 °C Storage temperature Tstg –40 to +125 °C Power dissipation Pd 260 mW Caution T A = 85 °C Exposure to Absolute Maximum Rating for extended periods may affect device reliability; exceeding the ratings could cause permanent damage. The parameters apply independently. RECOMMENDED OPERATING CONDITIONS (TA = 25 ˚C, GND = 0 V) Parameter Power supply voltage Symbol Conditions VCC MIN. TYP. 2.0 Unit 5.5 V Power supply voltage VDD1 Note 10.5 21.0 V Power supply voltage VDD1–VSS Note 20.5 31.0 V Power supply voltage VDD2a –1.0 +4.0 V Power supply voltage VDD2b –1.0 +4.0 V Power supply voltage VSS –10.0 –6.0 V Power supply voltage Vsb–VSS 31.0 V Note 15.0 MAX. Input voltage, high V IH –0.8 VCC VCC V Input voltage, low VIL 0 0.3 VCC V Operating ambient temperature TA –20 +70 °C Note Set the values of VDD1 and VSS to conform to VDD1–VSS specification value. 5 µPD16510 ELECTRICAL CHARACTERISTICS (Unless otherwise specified, VDD1 = +15 V, VDD2a = 0 V, VDD2b = +1.0 V, Vsb = +21.5 V, VCC = +2.5 V, VSS = –7.0 V, TA = 25 °C, GND = 0 V) Parameter Symbol Output voltage, high VH Output voltage, middle VMa Output voltage, middle VMb Output voltage, low VL Conditions MIN. IO = –20 µA IO = 20 µA TYP. MAX. Unit VDD1–0.1 VDD1 V VDD2a–0.1 VDD2a V VDD2b–0.1 VDD2b V VSS +0.1 VSS V Output voltage, sub high V subH IO = –20 µA Vsb–0.1 Vsb V Output voltage, sub low VsubL IO = 20 µA VSS +0.1 VSS V Output ON resistance RL IO = 10 mA 20 30 Ω Output ON resistance RM IO = ±10 mA 30 45 Ω Output ON resistance RH IO = –10 mA 30 40 Ω Output ON resistance Rsub 30 40 Ω Transmission delay time 1 T D1 200 ns Transmission delay time 2 T D2 200 ns Transmission delay time 3 T D3 200 ns Rise/Fall time 1 TP1 See Figure 1. Output Load Circuit. 500 ns Rise/Fall time 2 TP2 See Figure 2. Timing Chart. 500 ns Rise/Fall time 3 TP3 200 ns Consumption Current ICC Consumption Current IDD2a Consumption Current No load, see Figure 2. Timing Chart. See Figure 1. Output Load Circuit. 0.5 1.0 mA See Figure 3. Input Waveform. 3.0 5.0 mA IDD2b 3.0 5.0 mA Consumption Current lDD1 1.5 3.0 mA Consumption Current Isb 1.2 1.8 mA Figure 1. Output Load Circuit 2000 pF 2000 pF 1000 pF TO1 BO2 3000 pF 3000 pF 1000 pF BO1 TO2 2000 pF 6 2000 pF SUBO 1600 pF µPD16510 Figure 2. Timing Chart BI1, BI2 TI1, TI2 TD1 TD1 VMb VMa BO1, BO2 TO1, TO2 VL TP1 TP1 PG1, PG2 TD2 TD2 VH TO1, TO2 VMa TP2 TP2 SUBI TD3 TD3 VHH SUBO VL TP3 TP3 7 µPD16510 Figure 3. Input Waveform Input pulse timing diagram 63.5 µs 127 µs 2 µs Tl2 Tl1 Bl1 Bl2 PG1 2.5 µ s PG2 63.5 µ s 2.5 µ s 2 µs 16.7 ms SUBI Overlap section enlarged diagram Tl1 Bl1 Tl2 Bl2 0 8 0.7 1.4 2.1 2.8 3.5 4.2 4.9 µs µPD16510 APPLICATION CIRCUIT EXAMPLE VSS Vsb VCC VDD1 VSUB (substrate voltage) CCD 0.1 µF SUB 1 MΩ 1 SUBO Vsb 20 2 VSS VDD2b 19 3 BO1 BO2 18 4 VDD2a TO2 17 5 TO1 VDD1 16 6 VCC GND 15 7 Tl1 Tl2 14 8 PG1 PG2 13 9 Bl1 Bl2 12 NC 11 0.1 µF 0.1 µ F V1 SUB TG V1 0.1 µ F µ PD16510 SSG V2 V3 V4 0.1 µ F V2 V3 V4 10 SUBI 9 µPD16510 PACKAGE DRAWING 20 PIN PLASTIC SHRINK SOP (225mil) 20 11 P detail of lead end 1 H 10 A I E K F G J N B C D M L M NOTE Each lead centerline is located within 0.10 mm (0.004 inch) of its true position (T.P.) at maximum material condition. ITEM MILLIMETERS INCHES A 7.00 MAX. 0.276 MAX. B 0.575 MAX. 0.023 MAX. C 0.65 (T.P.) 0.026 (T.P.) D 0.22 +0.10 –0.05 0.009 +0.004 –0.003 E 0.1±0.1 0.004±0.004 F 1.45 MAX. 0.057 MAX. G 1.15±0.1 0.045 +0.005 –0.004 H 6.4±0.2 0.252±0.008 I 4.4±0.1 0.173 +0.005 –0.004 J 1.0±0.2 0.039 +0.009 –0.008 K 0.15 +0.10 –0.05 0.006 +0.004 –0.002 L 0.5±0.2 0.020 +0.008 –0.009 M 0.10 0.004 N 0.10 0.004 P 3˚ +7˚ –3˚ 3˚ +7˚ –3˚ P20GR-65-225C-1 10 µPD16510 RECOMMENDED SOLDERING CONDITIONS When soldering this product, it is highly recommended to observe the conditions as shown below. If other soldering processes are used, or if the soldering is performed under different conditions, please make sure to consult with our sales offices. For more details, refer to our document “SEMICONDUCTOR DEVICE MOUNTING TECHNOLOGY MANUAL” (C10535E). Surface mount device µPD16510GR-8JG: 20-pin plastic shrink SOP (225 mil) Process Conditions Symbol Infrared ray reflow Peak temperature: 235 °C or below (Package surface temperature), Reflow time: 30 seconds or less (at 210 °C or higher), Maximum number of reflow processes: 3 times. IR35-00-3 VPS Peak temperature: 215 °C or below (Package surface temperature), Reflow time: 40 seconds or less (at 200 °C or higher), Maximum number of reflow processes: 3 times. VP15-00-3 Wave soldering Solder temperature: 260 °C or below, Flow time: 10 seconds or less, Maximum number of flow processes: 1 time, Pre-heating temperature: 120 °C or below (Package surface temperature). WS60-00-1 Partial heating method Pin temperature: 300 °C or below, Heat time: 3 seconds or less (Per each side of the device). — Caution Apply only one kind of soldering condition to a device, except for “partial heating method”, or the device will be damaged by heat stress. 11 µPD16510 [MEMO] 12 µPD16510 [MEMO] 13 µPD16510 [MEMO] 14 µPD16510 NOTES FOR CMOS DEVICES 1 PRECAUTION AGAINST ESD FOR SEMICONDUCTORS Note: Strong electric field, when exposed to a MOS device, can cause destruction of the gate oxide and ultimately degrade the device operation. Steps must be taken to stop generation of static electricity as much as possible, and quickly dissipate it once, when it has occurred. Environmental control must be adequate. When it is dry, humidifier should be used. It is recommended to avoid using insulators that easily build static electricity. Semiconductor devices must be stored and transported in an anti-static container, static shielding bag or conductive material. All test and measurement tools including work bench and floor should be grounded. The operator should be grounded using wrist strap. Semiconductor devices must not be touched with bare hands. Similar precautions need to be taken for PW boards with semiconductor devices on it. 2 HANDLING OF UNUSED INPUT PINS FOR CMOS Note: No connection for CMOS device inputs can be cause of malfunction. If no connection is provided to the input pins, it is possible that an internal input level may be generated due to noise, etc., hence causing malfunction. CMOS device behave differently than Bipolar or NMOS devices. Input levels of CMOS devices must be fixed high or low by using a pull-up or pull-down circuitry. Each unused pin should be connected to VDD or GND with a resistor, if it is considered to have a possibility of being an output pin. All handling related to the unused pins must be judged device by device and related specifications governing the devices. 3 STATUS BEFORE INITIALIZATION OF MOS DEVICES Note: Power-on does not necessarily define initial status of MOS device. Production process of MOS does not define the initial operation status of the device. Immediately after the power source is turned ON, the devices with reset function have not yet been initialized. Hence, power-on does not guarantee out-pin levels, I/O settings or contents of registers. Device is not initialized until the reset signal is received. Reset operation must be executed immediately after power-on for devices having reset function. 15 µPD16510 [MEMO] The application circuits and their parameters are for reference only and are not intended for use in actual design-ins. No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Corporation. NEC Corporation assumes no responsibility for any errors which may appear in this document. NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a device described herein or any other liability arising from use of such device. No license, either express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Corporation or others. While NEC Corporation has been making continuous effort to enhance the reliability of its semiconductor devices, the possibility of defects cannot be eliminated entirely. To minimize risks of damage or injury to persons or property arising from a defect in an NEC semiconductor device, customers must incorporate sufficient safety measures in its design, such as redundancy, fire-containment, and anti-failure features. NEC devices are classified into the following three quality grades: "Standard", "Special", and "Specific". The Specific quality grade applies only to devices developed based on a customer designated "quality assurance program" for a specific application. The recommended applications of a device depend on its quality grade, as indicated below. Customers must check the quality grade of each device before using it in a particular application. Standard: Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots Special: Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) Specific: Aircrafts, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems or medical equipment for life support, etc. The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books. If customers intend to use NEC devices for applications other than those specified for Standard quality grade, they should contact an NEC sales representative in advance. Anti-radioactive design is not implemented in this product. M4 96.5