Filename: tfs 280g.doc Version 1.8 Vectron International 26.07.2010 Filter specification TFS 280G 1/5 Measurement condition Ambient temperature: Input power level: Source and load impedance: Terminating impedances * Input: Output: 22 0±2 50 Ω °C dBm 275 Ω || -7,7 pF 162 Ω || -10,6 pF Characteristics Remark: The reference level for the relative attenuation arel of TFS280G is the minimum of the pass band attenuation amin. This value is defined as the insertion loss ae. The centre frequency fc is the arithmetic mean value of the upper and lower frequencies at the 3 dB filter attenuation level relative to the insertion loss ae. The given values for the relative attenuation arel and the group delay ripple have to be reached at the frequencies given below, even if the centre frequency fc is shifted due to the temperature coefficient of frequency TCf in the operating temperature range and due to a production tolerance for the centre frequency fc. Data typ. value Insertion loss ae = amin 11,3 Nominal frequency fN - Centre frequency fc 280,0 Relative attenuation arel fN - 20 MHz ... fN + 20 MHz fN + fN + 10 32 40 MHz ... fN 32 MHz ... fN + 40 MHz ... fN + 220 MHz MHz MHz 0,8 Group delay ripple GDR fN – 17 MHz ... fN + 17 MHz dB limit max. 12 dB 280,0 MHz MHz - dB max. 1 dB 41 38 41 dB dB dB min. min. min. 40 37 40 dB dB dB 38 ns max. 75 ns Input power level - max. + 15 Operating temperature range - - 40 °C ... + 85 °C Storage temperature range Temperature coefficient of frequency - 40 °C ... + 85 °C TCf -87 dBm ppm/K - *) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference values only. Should there be additional questions, do not hesitate to ask for an application note or contact our design team. **) ∆f(Hz) = TCf(ppm/K) x (T-T0) x fTo(MHz) Generated: Checked / Approved: Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 280g.doc Version 1.8 Vectron International 26.07.2010 Filter specification TFS 280G 2/5 0 0.9 -1 0.84 -14 -2 0.78 -21 -3 0.72 -28 -4 0.66 -5 0.6 -6 0.54 -49 -7 0.48 -56 -8 0.42 -63 -9 0.36 -35 -42 -70 180 200 220 240 260 280 300 frequency in MHz 320 340 360 -10 252 380 257.6 263.2 268.8 274.4 280 285.6 frequency in MHz 291.2 296.8 302.4 delay in µs 0 -7 magnitude in dB magnitude in dB Filter characteristic 0.3 308 Construction and pin connection (All dimensions in mm) 7 5 280G ● U09 3 5 7 Date code: U V W ... Year + week 2006 2007 2008 0,1 1,1 120° +0,15 1,1 Input RF Return Input Ground Ground Output RF Return Output Ground Ground 1,8 Max. 1 Date code 0,64 3 5 - 0,10 1 1 2 3 4 5 6 7 8 2,54 50 Ohm Test circuit L1 2 1 6 SAW C1 L2 5 C2 3, 4, 7, 8 Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 280g.doc Version 1.8 Vectron International 26.07.2010 Filter specification TFS 280G 3/5 Stability characteristics 1. High Temperature (IEC 60068 -3-1) 1,000 hours at +85C 2. Low Temperature (IEC 60068 -3-1) 1,000 hours at – 40C 3. Humidity (IEC 60068 -2-78) 1,000 hours at 85% /85C 4. Thermal Shock ( IEC60068-2-14 ) -55 °C to 125°C / 30 min. each / 10 cycles 5. Vibration (IEC 60068 -2-6) 10 Hz to 500 Hz, 0,35 mm or 5g respectively, 1 octave per min, 10 cycles per plan, 3 plans 6. Shock (IEC 60068 -2-27) 500g, 1 ms, half sine wave, 3 shocks each plane 7. Reflow Profile ( defined at specification ) 260°C +/- 5°C for 10 seconds, 2 cycles 8. Solerability 235°C +/- 5°C for 15 seconds, 1 cycle 9. Pullability, Distortion according to MIL-STD 883 method 2004.5 Condition D This filter is RoHS compliant (2002/95/EG, 2005/618/EG) Packing IEC 286 – 3, with exception of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: reel of empty components at start: reel of empty components at start including leader: trailer: 3000 min. 300 mm min. 500 mm min. 300 mm Pull Off Direction P1 Tape (all dimensions in mm) W : 12,00 ± 0,3 Po : 4,00 ± 0,1 Do : 1,50 +0,1/-0 E : 1,75 ± 0,1 F : 5,50 ± 0,05 G(min) : 0,75 P2 : 2,00 ± 0,05 P1 : 8,00 ± 0,1 D1(min) : 1,50 Ao : 5,30 ± 0,1 Bo : 5,30 ± 0,1 Ct : 9,5 ± 0,1 t Po P2 G Ct Bo F G E Do PIN Marker W Tape & Reel: Ko Date Code Typ D1 Ao W 2 Reel (all dimensions in mm) A : 330 W1 : 12,4 +2/-0 W2(max) : 18,4 N(min) : 50 C : 13,0 +0,5/-0,2 C A N W 1 The minimum bending radius is 45 mm. Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 280g.doc Version 1.8 Vectron International 26.07.2010 Filter specification TFS 280G 4/5 Air reflow temperature conditions Conditions Average ramp-up rate (30°C to 217°C) > 100°C > 150°C > 217°C Peak temperature Time within 5°C of actual peak temperature Cool-down rate (Peak to 50°C) Time from 30°C to Peak temperature Exposure less than 3°C/second between 300 and 600 seconds between 240 and 500 seconds between 30 and 150 seconds max. 260°C between 10 and 30 seconds less than 6°C/second no greater than 300 seconds Chip-mount air reflow profile Temperature / °C max. 260°C 217°C max. 300 s 10 ... 30 s Time / s 30 ... 150 s Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 280g.doc Vectron International Version 1.8 Filter specification 26.07.2010 TFS 280G 5/5 History Version Reason of Changes Name Date 1.0 - new generation Steiner 20.08.2002 1.1 - change temperature, add 3dB passband requirement - relax stop-band limit lines according to larger temperature range Steiner 28.10.2002 1.2 - source and load impedance added - passband magnitude extended to +/-20MHz - Tk added Steiner 07.01.2003 1.3 - label changed to standard label Steiner 18.03.2003 1.4 - change pinning corresponding to customer demands - added operating temperature range to guaranty for samples delivered with date code R16 Chilla 23.04.2003 1.5 - added limit line at 37 dB Chilla 10.07.2003 1.6 - changed development specification to filter specification - added typical values - operating temperature range changed to –40 °C ... +80 °C - added terminating impedances Chilla 16.10.2003 1.7 - Chilla 03.03.2006 1.8 - Input power increased to +15dBm (was 10dBm) max Jaffer 26.07.2010 filter characteristics added test circuit updated stability characteristics updated air reflow temperature conditions updated Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.