CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS CF Chip Type, Standard series Ultra Low ESR, High ripple current. Load life of 2000 hours at 105°C. SMD type : Lead free reflow soldering condition at 260°C peak correspondence. Adapted to the RoHS directive (2002/95/EC). Specifications Item Performance Characteristics Category Temperature Range – 55 ~ +105°C Rated Voltage Range 2.5 ~ 25V Rated Capacitance Range 6.8 ~ 1500µF Capacitance Tolerance ± 20% at 120Hz, 20°C tan δ Not more than value of Standard ratings at 120Hz, 20°C ESR ( Not more than value of Standard ratings at 100kHz, 20°C 1) Leakage Current ( Not more than value of Standard ratings. 2) After 2 minute's application of rated voltage. 20°C Characteristics of Temperature Impedance Ratio Z+105°C / Z+20°C Z– 55°C / Z+20°C Endurance After 2000 hours' application of rated voltage at 105°C, capacitors meet the specified value for life characteristics listed at right. Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 20% of initial value ( 3) 150% or less of the initial specified value 150% or less of the initial specified value Initial specified value or less Damp Heat After 1000 hours' application of rated voltage at 60°C 90%RH, capacitors meet the specified value for life characteristics listed at right. Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 20% of initial value ( 3) 150% or less of the initial specified value 150% or less of the initial specified value Initial specified value or less Resistance to Soldering Heat To comply with recommended conditions for reflow soldering. Pre-heating shall be done at 150 ~ 200°C and for 60 ~ 180 sec. In the case of peak temp, less than 250°C, reflow soldering shall be within two times. In the case of peak temp, less than 260°C, reflow soldering shall be once. Measurement for solder temperature profile shall be made at the capacitor top and the terminal. Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 10% of initial value ( 3) 130% or less of the initial specified value 130% or less of the initial specified value Initial specified value or less Marking Navy blue print on the case top 1.25 1.25 (100kHz) 1 ESR measurements should be made at a point on the terminal nearest where the terminals protrude through the plastic platform. 2 Conditioning : If there is doubt about the measured result, measurement should be made again after the rated voltage is applied for 120 minutes at the temperature of 105°C. 3 Initial value : The value before test of examination of resistance to soldering. Type numbering system (Example : 6.3V 150µF) Dimensions Series Voltage ( j:6.3v) 0.5 MAX. E B±0.2 fD + 0.5 MAX. C±0.2 L +0.1 -0.4 H A±0.2 Plastic platform 0.3 MAX. Lot No. CF 150 j 6X1 Capacitance Positive Negative (mm) Size φD L A B C E H φ6.3 × 6L 6.3 φ8 × 7L 8.0 φ10 × 8L 10.0 φ10 × 10L 10.0 5.9 7.3 6.6 6.6 2.1 0.5 ~ 0.8 6.9 9.0 8.3 8.3 3.2 0.8 ~ 1.1 7.9 11.0 10.3 10.3 4.6 0.8 ~ 1.1 9.9 11.0 10.3 10.3 4.6 0.8 ~ 1.1 Voltage V 2.5 4 6.3 10 16 20 25 Code e g j A C D E Dimension table in next page. CAT.8100V CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS CF series Standard ratings Rated Voltage (V) (code) 2.5 (0E) 4 (0G) 6.3 (0J) 10 (1A) 16 (1C) 20 (1D) 25 (1E) Rated Capacitance (µF) 100 220 470 820 1500 100 150 220 330 470 680 820 82 100 120 150 220 330 470 470 680 47 56 120 150 150 270 330 470 560 33 39 56 82 150 180 220 22 39 68 82 120 6.8 10 22 47 Case Size φD×L (mm) tan δ Leakage Current (µA) ESR (mΩ) (at 100kHz 20˚C) Rated ripple (mArms) Part Number 6.3 × 6 6.3 × 6 8×7 10 × 8 10 × 10 6.3 × 6 6.3 × 6 8×7 8×7 10 × 8 10 × 8 10 × 10 6.3 × 6 6.3 × 6 6.3 × 6 8×7 8×7 10 × 8 10 × 8 10 × 10 10 × 10 6.3 × 6 6.3 × 6 8×7 8×7 10 × 8 10 × 8 10 × 8 10 × 10 10 × 10 6.3 × 6 6.3 × 6 8×7 8×7 10 × 8 10 × 8 10 × 10 6.3 × 6 8×7 10 × 8 10 × 8 10 × 10 6.3 × 6 8×7 10 × 8 10 × 10 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 100 110 235 410 750 80 120 176 264 376 544 656 103 126 151 189 277 416 592 592 856 94 112 240 300 300 540 660 940 1120 106 124 179 262 480 576 704 88 156 272 328 480 85 125 275 587 22 20 20 17 13 22 22 21 21 17 17 13 23 23 23 22 22 18 18 16 14 26 25 23 23 21 20 20 16 15 31 31 30 28 25 25 20 50 45 40 40 35 80 60 50 45 2600 2800 3300 4400 4700 2600 2800 3200 3400 4200 4400 4800 2600 2800 3000 3200 3400 4200 4300 4600 5000 2600 2500 3000 3200 3300 3600 3700 4600 4800 2400 2400 2900 3200 3500 3600 3900 1700 2000 2600 2600 2800 1200 1600 2200 2400 PCF0E101MCL1GS PCF0E2211MCL1GS PCF0E471MCL1GS PCF0E821MCL1GS PCF0E152MCL1GS PCF0G101MCL1GS PCF0G151MCL1GS PCF0G221MCL1GS PCF0G331MCL1GS PCF0G471MCL1GS PCF0G681MCL1GS PCF0G821MCL1GS PCF0J820MCL1GS PCF0J101MCL1GS PCF0J121MCL1GS PCF0J151MCL1GS PCF0J221MCL1GS PCF0J331MCL1GS PCF0J471MCL6GS PCF0J471MCL1GS PCF0J681MCL1GS PCF1A470MCL1GS PCF1A560MCL1GS PCF1A121MCL1GS PCF1A151MCL6GS PCF1A151MCL1GS PCF1A271MCL1GS PCF1A331MCL1GS PCF1A471MCL1GS PCF1A561MCL1GS PCF1C330MCL1GS PCF1C390MCL1GS PCF1C560MCL1GS PCF1C820MCL1GS PCF1C151MCL1GS PCF1C181MCL1GS PCF1C221MCL1GS PCF1D220MCL1GS PCF1D390MCL1GS PCF1D680MCL1GS PCF1D820MCL1GS PCF1D121MCL1GS PCF1E6R8MCL1GS PCF1E100MCL1GS PCF1E220MCL1GS PCF1E470MCL1GS No marked, 1 will be put at 12th digit of type numbering system. : In this case, 6 will be put at 12th digit of type numbering system. Rated Ripple (mArms) at 105°C 100kHz Taping specifications are given in page 24. Recommended land size, soldering by reflow are given in page 25, 26. Please refer to page 3 for the minimum order quantity. CAT.8100V