General purpose (dual digital transistors) EMG6 / UMG6N / FMG6A zDimensions (Unit : mm) zFeatures 1) Two DTC144T chips in a EMT or UMT or SMT package. R1 (3) R1 DTr2 DTr1 (4) (5) (4) (5) R1 R1 DTr2 Each lead has same dimensions ROHM : EMT5 DTr1 (2) (1) zAbsolute maximum ratings (Ta=25°C) 2.1 Unit Collector-base voltage VCBO 50 V Collector-emitter voltage VCEO 50 V 0.1Min. Emitter-base voltage VEBO 5 V 100 mA IC EMG6 / UMG6N 150(TOTAL) Pc 0.7 Limits 0~0.1 Symbol Collector current 2.0 1.25 0.15 Parameter (1) (5) (2) 0.2 (4) UMG6N 1.3 R1=47kΩ 0.9 R1=47kΩ Collector power dissipation 0.5 0.5 1.0 1.6 (1) (2) (3) 0.5 FMG6 (1) 0.65 0.65 (2) (3) (3) 1.2 1.6 0.13 zEquivalent circuit EMG6 / UMG6N (4) (5) 0.22 EMG6 Each lead has same dimensions ROHM : UMT5 EIAJ : SC-88A mW 300(TOTAL) FMG6A Junction temperature Tj 150 °C Storage temperature Tstg −55 to +150 °C 2.9 0.8 1.1 (5) (1) zPackage, marking, and packaging specifications 0.95 0.95 1.9 (3) (4) (2) 0.3 FMG6A 1.6 UMG6N FMG6A Package EMT5 UMT5 SMT5 Marking Code G6 T2R G6 TR G6 T148 Basic ordering unit (pieces) 8000 3000 3000 www.rohm.com c 2009 ROHM Co., Ltd. All rights reserved. ○ 2.8 0.3Min. ROHM : SMT5 EIAJ : SC-74A 1/2 0~0.1 EMG6 0.15 Type Each lead has same dimensions 2009.02 - Rev.B Data Sheet EMG6 / UMG6N / FMG6A zElectrical characteristics (Ta=25°C) Symbol Min. Typ. Max. Unit Collector-base breakdown voltage Parameter BVCBO 50 − − V IC=50µA Collector-emitter breakdown voltage BVCEO 50 − − V IC=1mA Emitter-base breakdown voltage Collector cutoff current BVEBO ICBO 5 − − − − 0.5 V µA IE=50µA VCB=50V Emitter cutoff current Collector-emitter saturation voltage IEBO − − 0.5 µA VEB=4V VCE(sat) − − 0.3 V IC/IB=10mA/1mA hFE 100 250 600 − Transition frequency fT − 250 − MHz Input resistance R1 32.9 47 61.1 kΩ DC current transfer ratio Conditions VCE/IC=5V/1mA VCE=10V, IE= −5mA, f=100MHz ∗ − ∗Transition frequency of the device. 1k VCE=5V DC CURRENT GAIN : hFE 500 200 Ta=100°C 25°C −40°C 100 50 20 10 5 2 1 100µ 200µ 500µ 1m 2m 5m 10m 20m 50m 100m COLLECTOR CURRENT : IC (A) Fig.1 DC current gain vs. collector current www.rohm.com c 2009 ROHM Co., Ltd. All rights reserved. ○ COLLECTOR SATURATION VOLTAGE : VCE(sat) (V) zElectrical characteristics curves 1 lC/lB=10 500m 200m Ta=100°C 25°C −40°C 100m 50m 20m 10m 5m 2m 1m 100µ 200µ 500µ 1m 2m 5m 10m 20m 50m 100m COLLECTOR CURRENT : IC (A) Fig.2 Collector-emitter saturation voltage vs. collector current 2/2 2009.02 - Rev.B Appendix Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuel-controller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact your nearest sales office. ROHM Customer Support System www.rohm.com Copyright © 2009 ROHM Co.,Ltd. THE AMERICAS / EUROPE / ASIA / JAPAN Contact us : webmaster @ rohm.co. jp 21 Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan TEL : +81-75-311-2121 FAX : +81-75-315-0172 Appendix-Rev4.1