TFS35G - Vectron International

Filename: TFS35G.doc
Version 2.0
Vectron International
11.10.2012
Filter specification
TFS 35G
1/5
Measurement condition
Ambient temperature:
Input power level:
Terminating impedance: *
Input:
Output:
25
0
°C
dBm
469.96 Ω || -28.72 pF
956.93 Ω || -10.11 pF
Source impedance:
Load impedance:
500 Ω.
1000 Ω.
Characteristics
Remark:
The reference level for the relative attenuation arel of the TFS 35G is the minimum of the pass band attenuation amin. The minimum of the pass band
attenuation amin is defined as the insertion loss ae. The centre frequency fc is the arithmetic mean value of the upper and lower frequencies at the 3 dB
filter attenuation level relative to the insertion loss ae. The nominal frequency fN is fixed at 35.42 MHz without any tolerance. The given values for both the
relative attenuation arel and the group delay ripple have to be achieved at the frequencies given below even if the centre frequency fc is shifted due to the
temperature coefficient of frequency TCf in the operating temperature range and due to a production tolerance for the centre frequency fc.
Data
typ. value
Insertion loss
(reference level)
ae
Nominal frequency
fN
Centre frequency
fC
Passband (1)
PB1
Passband (2)
PB2
Pass band ripple in PB1
Bandwidth
35.42
dB
max.
MHz
17
dB
35.42
MHz
fC ± 0.80 MHz
-
fC ± 1.023 MHz
0.7
dB
max.
1.6
dB
2.29
2.61
MHz
MHz
min.
min.
1.7
MHz
2.046 MHz
dB
dB
dB
dB
dB
µs
max.
max.
min.
min.
min.
max.
1.6
3.0
25
25
15
1.7
BW
1.6 dB
3
dB
Relative attenuation
34.620
34.397
0.420
38.443
62.000
Group delay
12.9
tolerance / limit
MHz
MHz
MHz
MHz
MHz
arel
…
…
…
…
…
36.220 MHz
36.443 MHz
32.397 MHz
62.000 MHz
70.420 MHz
mean value in PB1
Group delay ripple within PB1
0.7
0.9
40
32
22
1.2
ns
max.
350
Deviation from linear phase within PB1
4
°
max.
7
°
Input/Output return loss within PB1
4
dB
min.
2
dB
Input power level
-
max.
0
dBm
-
- 40 °C ... + 85°C
Operating temperature range
190
dB
dB
dB
dB
dB
µs
OTR
Storage temperature range
Temperature coefficient of frequency
TCf **
-18
ns
- 55 °C ... + 125°C
ppm/K
-
*) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference values
only. Should there be additional questions do not hesitate to ask for an application note or contact our design team.
**) ∆f(Hz) = TCf(ppm/K) x (T-T0) x fTo(MHz).
Generated:
Checked / Approved:
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or
information.
Filename: TFS35G.doc
Version 2.0
Vectron International
11.10.2012
Filter specification
TFS 35G
2/5
Filter characteristic
1.67
-1
1.598
-20
-2
1.526
-30
-3
1.454
-40
-4
1.382
-5
1.31
-6
1.238
-70
-7
1.166
-80
-8
1.094
-50
-60
-90
-100
15
-9
19
23
27
31
35
39
frequency in MHz
43
47
51
-10
33.44
55
delay in µs
0
-10
magnitude in dB
magnitude in dB
insertion loss: -12.87 dB
0
1.022
33.84
34.24
34.64
35.04
35.44
35.84
frequency in MHz
36.24
36.64
37.04
0.95
37.44
Construction and pin connection
(All dimensions in mm)
13,6 Max.
1
6,8 Max.
TFS 35G
B19
date -code:
B
C
D
...
year + week
2011
2012
2013
...
date-code
Unbalanced :
2
1
2,54 ± 0,15
2,0 Max.
2,54 ± 0,15
1,5
3
4
12
Pin
Pin
Pin
Pin
Pin
Pin
Pin
Pin
Pin
Pin
6
9
10
8
0,8
Input
Input RF Return
Output
Output RF Return
Package Ground
Balanced :
5
11
11
12
5
6
1-4, 7-10
11
12
5
6
1-4, 7-10
Input
Input
Output
Output
Package Ground
7
0,1
500 Ω x 1000 Ω Test circuit:
1
2
3
4
12
500 Ω
L1
1
5
L2
2
1000Ω
Ω
Ω
6
11
10
9
8
7
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or
information.
Filename: TFS35G.doc
Version 2.0
Vectron International
11.10.2012
Filter specification
TFS 35G
3/5
Stability characteristics, reliability
After the following tests the filter shall meet the whole specification:
1. Shock:
500g, 1 ms, half sine wave, 3 shocks each plane;
DIN IEC 68 T2 - 27
2. Vibration:
10 Hz to 500 Hz, 0,35 mm or g respectively, 1 octave per min, 10 cycles per plane, 3 planes;
DIN IEC 68 T2 - 6
3. Change of
temperature:
4. Resistance to
solder heat (reflow):
5. ESD
-55 °C to 125°C / 30 min. each / 10 cycles
DIN IEC 68 part 2 – 14 Test N
reflow possible: three times max.;
for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4;
ANSI/ESD S20.20-1999, class 1A for HBM
This filter is RoHS compliant (2002/95/EG, 2005/618/EG)
Packing
Tape & Reel:
IEC 286 – 3, with exception of value for N and minimum bending radius;
tape type II, embossed carrier tape with top cover tape on the upper side;
max. pieces of filters per reel:
reel of empty components at start:
reel of empty components at start including leader:
trailer:
1700
min. 300 mm
min. 500 mm
min. 300 mm
Pull Off Direction
Tape (all dimensions in mm)
W
:24,00 +0,30/-0,10
Po
:4,00
± 0,1
Do
:1,50
+0,1/-0
E
:1,75
± 0,10
F
:11,50 ± 0,10
G(min)
:0,60
P2
:2,00
± 0,1
P1
:12,00 ± 0,1
D1(min)
:1,50
Ao
:7,10
± 0,10
Bo
:13,90 ± 0,10
Ct
:21,5
± 0,1
P1
Date Code
Po
Do
P2
W
G
Ct
Bo
F
G
E
t
Ko
Typ
PIN Marker
D1
Ao
W 2
Reel (all dimensions in mm)
A
: 330
W1
:24,4
+2/-0
W2(max) :30,4
N(min)
: 60
C
:13,0
+0,5/-0,2
C
A
N
W 1
The minimum bending radius is 45 mm.
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or
information.
Filename: TFS35G.doc
Version 2.0
Vectron International
11.10.2012
Filter specification
TFS 35G
4/5
Air reflow temperature conditions
Conditions
Average ramp-up rate (30°C to 217°C)
> 100°C
> 150°C
> 217°C
Peak temperature
Time within 5°C of actual peak temperature
Cool-down rate (Peak to 50°C)
Time from 30°C to Peak temperature
Exposure
less than 3°C/second
between 300 and 600 seconds
between 240 and 500 seconds
between 30 and 150 seconds
max. 260°C
between 10 and 30 seconds
less than 6°C/second
no greater than 300 seconds
Chip-mount air reflow profile
Temperature / °C
max. 260°C
217°C
max. 300 s
10 ... 30 s
Time / s
30 ... 150 s
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or
information.
Filename: TFS35G.doc
Vectron International
Version 2.0
Filter specification
11.10.2012
TFS 35G
5/5
History
Version
Reason of Changes
Name
Date
1.0
- Generation of development specification (based on TFS35GS01)
TCUK
06.02.2012
1.1
- Add typ value, add plots and move from dev to filter spec.
- Typo, change 1dB bw to 1.6dB to complement PB1.
TCUK
08.08.2012
TCUK
11.10.2012
2.0
- Changed ‘Group delay ripple within PB1’ from 300 to 350ns as per customer agreement
- (see email from customer 10/10/2012 :15:03pm)
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or
information.