Filename: tfs 420d.doc Version 2.0 Vectron International 25.11.2013 Filter specification TFS 420D 1/5 Measurement condition Ambient temperature: Input power level: Terminating impedance: Input: Output: 23 0 °C dBm 181Ω || -0.2pF 181Ω || -0.2pF Characteristics Remark: The reference level for the relative attenuation arel of the TFS 420D is the minimum of the pass band attenuation amin. The minimum of the pass band attenuation amin is defined as the insertion loss ae. The center frequency fc is the arithmetic mean value of the upper and lower frequencies at the 2 dB filter attenuation level relative to the insertion loss ae. The nominal frequency fN is fixed at 420.0 MHz without any tolerance. The given values for both the relative attenuation arel and the pass band ripple have to be achieved at the frequencies given below even if the center frequency fc is shifted due to the temperature coefficient of frequency TCf within the operating temperature range and due to a production tolerance for the center frequency fc. Data typ. value ae=amin Insertion loss (Reference level) Nominal frequency Center frequency … … … … … max. 3.5 dB - fc 420.0 MHz 1.5 dB *) max. dB dB dB dB dB min. min. min. min. min. 50 30 20 40 57 dB dB dB dB dB - min. 20.0 dB **) - max. 10.0 dBm - max. 12.0 V 420.0 MHz 2.0 dB arel Relative attenuation MHz MHz MHz MHz MHz dB fN Pass band ripple fN ± 10 MHz 320.0 365.0 445.0 477.5 547.5 2.7 tolerance / limit 340.0 385.0 477.5 502.5 572.5 MHz MHz MHz MHz MHz Intermodulation 65 50 25 55 70 IP3 Input power level Permissible DC voltage VDC Operating temperature range OTR Storage temperature range Temperature coefficient of frequency TCf - -25 °C ... +75 °C - -40 °C ... +85 °C -65 ppm/K - *) 1.5 dB over fN ± 10 MHz at ambient temperature (23 °C). **) modulation signals: fN + 1 MHz and fN + 2 MHz, each of 10 dBm Generated: Checked / Approved: Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 420d.doc Version 2.0 Vectron International 25.11.2013 Filter specification TFS 420D 2/5 Filter characteristic insertion loss: -2.68 dB 0 0 -1 -10 -2 -20 magnitude in dB magnitude in dB -3 -30 -40 -50 -4 -5 -6 -7 -60 -8 -70 -9 -80 320 340 360 380 400 420 440 460 frequency in MHz 480 500 520 540 -10 397.75 560 401.75 405.75 409.75 413.75 417.75 421.75 frequency in MHz 425.75 429.75 433.75 437.75 Construction and pin connection (All dimensions in mm) 7 5 420D ● D48 3 7 0,1 1,1 120° +0,15 1,1 Date code: D E F ... Year + week 2013 2014 2015 1,8 Max. 1 Date code Input Ground Ground Ground Output Ground Ground Ground 0,64 3 5 - 0,10 1 1 2 3 4 5 6 7 8 5 2,54 50 Ω Test circuit L1 1 L2 5 SAW C1 C2 2, 3, 4, 6, 7, 8 Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 420d.doc Version 2.0 Vectron International 25.11.2013 Filter specification TFS 420D 3/5 Stability characteristics, reliability After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 1 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10 Hz to 500 Hz, 0.35 mm or 5 g respectively, 1 octave per min, 10 cycles per plane, 3 planes; DIN IEC 68 T2 - 6 3. Change of temperature: 4. Resistance to solder heat (reflow): -55 °C to 125°C / 15 min. each / 100 cycles DIN IEC 68 part 2 – 14 Test N reflow possible: three times max.; for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4; This filter is RoHS compliant (2011/65/EU) Packing Tape & Reel: IEC 286 – 3, with exception of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: reel of empty components at start: reel of empty components at start including leader: trailer: 3000 min. 300 mm min. 500 mm min. 300 mm Pull Off Direction Tape (all dimensions in mm) W : 12,00 Po : 4,00 Do : 1,50 E : 1,75 F : 5,50 G(min) : 0,75 P2 : 2,00 P1 : 8,00 D1(min) : 1,50 Ao : 5,30 Bo : 5,30 Ct : 9,2 ± 0,1 P1 t PIN Marker Po P2 W G Ct Bo F G E Do Ko Date Code Typ D1 Ao W 2 Reel (all dimensions in mm) A : 330 W1 : 12,4 +2/-0 W2(max) : 18,4 N(min) : 50 C : 13,0 C A N W 1 The minimum bending radius is 45 mm. Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 420d.doc Version 2.0 Vectron International 25.11.2013 Filter specification TFS 420D 4/5 Air reflow temperature conditions Conditions Average ramp-up rate (30°C to 217°C) > 100°C > 150°C > 217°C Peak temperature Time within 5°C of actual peak temperature Cool-down rate (Peak to 50°C) Time from 30°C to Peak temperature Exposure less than 3°C/second between 300 and 600 seconds between 240 and 500 seconds between 30 and 150 seconds max. 260°C between 10 and 30 seconds less than 6°C/second no greater than 300 seconds Chip-mount air reflow profile Temperature / °C max. 260°C 217°C max. 300 s 10 ... 30 s Time / s 30 ... 150 s Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 420d.doc Vectron International Version 2.0 Filter specification 25.11.2013 TFS 420D 5/5 History Version Reason of Changes Name Date 1.0 - generate according customer requirement specification Dr. Sabah 28.06.2001 1.1 - add of relative attenuation fN - 35 MHz ... fN - 55 MHz min. 30,0 dB - add of IP3 (min. 20 dBm) - add of DC voltage 12 V - add of typ. Value in pass band 1,50 dB Dr. Sabah 06.07.2001 1.2 - add of typ. value of 60 dB (fN +127,5 MHz ... fN +152,5 MHz) Dr. Sabah 11.07.2001 1.3 - add of 50 Ω matching circuit Dr. Sabah 13.07.2001 1.4 - correct of 50 Ω matching circuit - change from development specification to filter specification - add of typical data and terminating impedance Dr. Sabah 07.01.2002 - changed maximum insertion loss from 3.0 dB to 3.5 dB Schönbein 25.11.2013 2.0 Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.