Filename: tfs 211-1.doc Version 1.8 VI TELEFILTER 03.08.2004 Filter specification TFS 211-1 1/5 Measurement condition Ambient temperature: 23 C Input power level: 10 dBm Terminating impedance: Input: 280 II -3,7 pF Output: 280 II -3,7 pF External coil: 127 nH The filter supports bursted GMSK and EDGE modulation. Characteristics Remark: Reference level for the relative attenuation arel of the TFS 211-1 is the filter attenuation at 211 MHz. The filter attenuation at 211 MHz is called insertion loss ae. The centre frequency fc is the arithmetic mean value of the upper and lower frequencies at the 3 dB filter attenuation level relative to the insertion loss ae. The given values for the relative attenuation arel and for the group delay ripple have to be reached at the frequencies given below also if the centre frequency fc is shifted due to the temperature coefficient of frequency TCf in the operating temperature range and due to a production tolerance for the centre frequency fc. Data typ. value Insertion loss (Reference level) a e = amin Centre frequency fc Nominal frequency fN kHz kHz kHz kHz MHz ... ... ... ... fN fN fN fN ± ± ± ± 400 600 800 100 6,5 dB 211,0 MHz ± 25 kHz kHz min 215 - max max max kHz kHz kHz MHz - min min min min 3 25 35 40 dB dB dB dB max 5 s max 1,0 s GD Group delay ripple fN ± 50 kHz Out of band intermodulation Input signals at 211,8 and 212,6 MHz at +10 dBm Input signals at 210,2 and 209,4 MHz at +10 dBm Input power level for less than 1 hour over life time fN ± 800 kHz ... fN ± 3 MHz fN ± 3 MHz ... fN ± 100 MHz 3,4 s –71 –71 dBm dBm - fN ± 100 kHz Operating temperature range Frequency inversion temperature dB dB dB max max max max 15 25 22 25 dBm dBm dBm dBm min 10 dB - 5 C ... + 80 C - 40 C … + 85 C Storage temperature range Temperature coefficient of frequency 1,5 2 3 kHz kHz kHz kHz Group delay at fN Return loss (S11/S22) max 211,0 MHz 270 Relative attenuation a rel fN ... fN ± 50 fN ± 50 kHz ... fN ± 80 fN ± 80 kHz ... fN ± 100 ± 200 ± 400 ± 600 ± 800 dB 211,0 3dB Bandwidth fN fN fN fN 4,5 tolerance / limit ca. - 0,036 + 20 ppm/K C Generated: Checked / Approved: Tele Filter GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 211-1.doc Version 1.8 VI TELEFILTER 03.08.2004 Filter specification Construction, pin connection and 50 TFS 211-1 2/5 - matching network 1 2 3 4 5 S211/1 N07 Output Ground External Coil Ground Ground 6 Input 7 Ground 8 Ground 9 Ground 10 Ground Date Code Date Code: L M N ... 1 2 3 10 4 9 5 8 7 Year + week 1999 2000 2001 6 50 Ohm matching networks C1 C2 1 6 3 L3 L1 L2 2,4,5,7,8,9,10 L4 1 6 3 C3 L5 L3 C4 2,4,5,7,8,9,10 Tele Filter GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 211-1.doc Version 1.8 VI TELEFILTER 03.08.2004 Filter specification TFS 211-1 3/5 Stability Characteristics After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 18 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10 Hz to 500 Hz, 0,35 mm or 5g respectively, 1 octave per min, 10 cycles per plan, 3 plans; DIN IEC 68 T2 - 6 3. Damp heat: (cycle) 25 °C to 55°C / 95% r.H. / 10 cycles DIN IEC 68 - 2 – 30 Db 4. Resistance to solder heat (reflow): 5. ESD max. 2 times reflow process; for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4; MIL-STD-883E using coupling network of ISO 10605 and EN 6100-4-2 HBM:250V; MM:200V; Packing Tape & Reel: IEC 286 – 3, with exeption of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters peer reel: reel of empty components at start: reel of empty components at start including leader: trailer: 3000 min. 300 mm min. 500 mm min. 300 mm Pull Off Direction Tape (all dimensions in mm) W : 16,00 ± 0,3 Po : 4,00 ± 0,1 Do : 1,50 +0,1/-0 E : 1,75 ± 0,10 F : 7,50 ± 0,10 G(min) : 0,60 P2 : 2,00 ± 0,1 P1 : 12,00 ± 0,1 D1(min) : 1,50 +0,1/-0 Ao : 7,60 ± 0,10 Bo : 9,60 ± 0,10 Ct : 13,5 t Ko P1 Date Code Do Typ Po PIN Marker P2 D1 Ao W 2 Reel (all dimensions in mm) A : 330 W1 : 16,4 W2(max) : 22,4 N(min) : 50 C : 13,0 C A N W 1 The minimum bending radius is 45 mm. Tele Filter GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 211-1.doc Version 1.8 VI TELEFILTER 03.08.2004 Filter specification TFS 211-1 4/5 Air reflow temperature conditions 1st and 2nd air reflow profile Name: Temperature: Time: pre-heating periods 150 °C - 170 °C 60 sec. - 90 sec. main-heating periods over 200 °C 20 sec. - 25 sec. peak temperature 255 °C ± 5 °C Chip-mount air reflow profile 260 240 220 200 temperature / °C 180 160 140 120 100 80 60 40 20 0 0 20 40 60 80 100 120 140 160 180 200 220 240 time / s ec. Table for temperature vs. time during the air reflow process Tolerance of temperatures: ± 5 °C time / sec. 0 10 20 30 40 50 60 70 80 90 100 110 120 130 temperature / °C 23 34 46 60 80 103 121 134 143 150 154 156 158 159 time / sec. 140 150 160 170 180 190 195 200 205 210 215 220 230 240 temperature / °C 160 161 164 170 180 205 230 255 230 205 180 165 140 120 Tele Filter GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 211-1.doc VI TELEFILTER Version 1.8 Filter specification 03.08.2004 TFS 211-1 5/5 History Version Reason of Changes Name Date 1.3 Change date code to weekly date code. Change filter labelling. Correct tape and reel information. Dr. Wall 13.07.2000 1.4 Change stop band attenuation and operating temperature range according to customer’s request. Dr. Wall 20.12.2000 1.5 Change stop band attenuation in frequency range fN ± 600 kHz ... fN ± 800 kHz according to customer requests. Add maximum input power. Add support of bursted GMSK and EDGE modulation. Dr. Wall 22.01.2001 1.6 Change power handling, intermodulation and operating temperature range according to customer’s request. Dr. Wall 15.02.2001 1.7 Change input power level for final test from 0 dBm to 10 dBm Dr. Wall 27.02.2001 1.8. ESD limits added Strehl 03.09.2004 Tele Filter GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.